PU Injection Grouting Explained: How to Stop Active Water Leakage in Basements, Lift Pits and Concrete Cracks
A practical guide to polyurethane injection waterproofing, where it works, how it is applied, and what it costs in India.
Imagine walking into your basement after a heavy monsoon shower and discovering water coming through a crack in the retaining wall.
Or opening a lift pit and finding water continuously seeping through the wall-floor junction.
The usual reaction?
"Sir, waterproofing karwa dete hain."
Someone suggests a cementitious coating. Another recommends crystalline waterproofing. A third suggests filling the crack with epoxy mortar.
All reasonable products, but are they suitable when water is actively flowing?
Not necessarily.
When water is continuously entering through a concrete crack or construction joint, applying another coating over the wet surface is often not the solution.
The water pressure remains behind the coating, and unless the source of leakage is addressed, the repair may fail.
This is where polyurethane injection grouting, commonly called PU injection waterproofing, becomes useful.
It allows us to treat water leakage from within the concrete rather than simply covering the visible damp patch.
Let's understand how it works.
1. What Is PU Injection Grouting?

PU injection grouting is a specialised waterproofing repair method used to stop water entering through cracks, joints and voids in concrete structures.
The process involves injecting a liquid polyurethane resin into the affected area using a pressure grouting pump.
Certain PU injection resins react with water and expand to form foam.
As the foam expands, it fills the available spaces within the crack or joint and restricts the movement of water.
In simple terms:
Instead of applying waterproofing over the crack, we inject the waterproofing material into the crack itself.
This is particularly useful in underground structures where external waterproofing is no longer accessible.
How does the resin stop water?
The process is relatively straightforward.
-
Liquid PU resin enters the crack through a drilled injection point.
-
The resin encounters moisture or flowing water.
-
A chemical reaction begins, causing the resin to expand.
-
The expanding foam fills the available voids and restricts water movement.
-
Once the reaction is complete, the material forms a barrier within the leakage path.
Depending on the chemistry, the cured material may be rigid or flexible, and its cell structure and long-term behaviour will vary.
Important: Not every PU injection resin works in the same way. Some products are designed for rapid temporary water stopping, while others are intended for more durable, flexible sealing.
Always check the manufacturer's Technical Data Sheet (TDS) before selecting a resin.
2. Where Is PU Injection Waterproofing Used?
Over four decades of working with construction chemicals, we have encountered many situations where the visible leakage was only a small part of the actual problem.
Water can travel through concrete joints, honeycombed areas and interconnected cracks before appearing at a completely different location.
PU injection is particularly useful in the following situations.
Basement Walls and Raft Slabs
Basements are especially vulnerable when groundwater rises during the monsoon.
Water pressure builds outside the retaining walls and beneath the raft slab.
If there are cracks, honeycombs or poorly treated construction joints, water may enter through these weak locations.
PU injection can be carried out from the accessible internal face, avoiding the need for immediate external excavation.
However, widespread seepage or a defective waterproofing system may require a more comprehensive repair strategy.
Lift Pits
Lift pits are among the most common locations for active water leakage.
They are usually situated at the lowest level of a building, where groundwater pressure can become significant.
Typical leakage locations include:
-
Wall-floor junctions
-
Construction joints
-
Cracks in retaining walls
-
Honeycombed concrete
-
Pipe penetrations
PU injection is often suitable for stopping localised water ingress.
The lift equipment must be protected, and electrical safety precautions are essential before any repair begins.
Underground Water Tanks
Leakage can develop at construction joints, wall-floor junctions and cracks in underground tanks.
PU injection may be used to stop active water ingress, particularly where water is entering from outside.
However, if the injected material may contact drinking water, appropriate potable-water suitability documentation must be verified.
A product suitable for basement leakage is not automatically approved for drinking-water contact.
Construction Joints and Cold Joints
Concrete cannot always be poured continuously.
When one concrete pour is completed and another begins later, a construction joint is formed.
If the joint has not been properly treated with a waterstop or suitable joint waterproofing system, it can become a leakage path.
Cold joints caused by interruptions in concrete supply can create similar problems.
PU injection is frequently used to treat these locations after construction.
Cracks in Concrete Slabs
Sometimes water appears on the underside of a concrete slab.
The actual entry point may be several metres away from the visible damp patch.
Injection can help seal the crack or leakage path, but the source of water must also be investigated.
If the crack is structural or continues to move significantly, additional engineering assessment is necessary.
3. PU Injection or Epoxy Injection: Which One Should You Use?

Â
This is one of the most common questions we receive.
Both products are injected into concrete, but their purposes are different.
| Situation | PU Injection | Epoxy Injection |
|---|---|---|
| Active water leakage | Usually preferred | Generally unsuitable while water is flowing |
| Dry structural crack | Not normally the first choice | Often preferred |
| Water-bearing construction joint | Suitable resin systems available | Generally not preferred |
| Restoring structural continuity | Not intended for this | Suitable structural injection grades |
| Minor crack movement | Flexible PU grades may accommodate movement | Rigid epoxy generally cannot |
| Primary objective | Stop water ingress | Restore bonding and structural continuity |
A simple way to remember
PU injection is primarily for stopping water.
Structural epoxy injection is primarily for restoring strength and bonding across suitable cracks.
But there is an important distinction.
A water-reactive PU foam used to stop active leakage may not always be the best material for permanent sealing.
In some situations, the correct repair involves two stages:
Stage 1: Stop the active water flow using a suitable foaming PU resin.
Stage 2: Carry out secondary injection with a compatible flexible, non-foaming resin where required by the repair specification.
This is particularly relevant for critical underground structures.
Also, products such as epoxy bonding pastes and structural epoxy injection resins are not interchangeable. The resin must be specifically suitable for injection into the crack.
4. How Is PU Injection Grouting Actually Done?

Â
Although the concept is simple, successful injection requires experience.
The most important part is not operating the pump.
It is understanding where the water is travelling and how the injected resin will behave.
Step 1: Identify the Leakage Path
The applicator first examines the affected area.
The objective is to identify:
-
The visible leakage points
-
Direction and extent of the crack
-
Construction joints
-
Water pressure
-
Approximate concrete thickness
-
Whether the crack is active or dormant
Sometimes the water appears at one location but enters the concrete elsewhere.
This is why simply injecting at the visible wet patch may not solve the problem.
Step 2: Mark the Injection Points
Injection points are marked along the crack or construction joint.
For many conventional crack-injection applications, packer spacing may be approximately 150 to 300 mm, depending on crack width, concrete thickness and site conditions.
This is only an indicative range.
Actual spacing must be determined by the applicator and the injection system being used.
Step 3: Drill the Injection Holes
Holes are drilled into the concrete to intersect the crack.
A common approach is to drill at approximately 45 degrees to the concrete surface, offset from the crack.
The objective is to reach the crack within the concrete rather than simply injecting material into its visible opening.
Drill diameter depends on the packer selected. Mechanical packers commonly require holes in the approximate 10 to 14 mm range, although other sizes are used.
Drilling depth and angle must account for reinforcement, concrete thickness and the crack location.
Step 4: Install Injection Packers
Mechanical injection packers are fitted into the drilled holes.
These are small metal or plastic fittings with valves that allow resin to be pumped into the concrete under controlled pressure.
The packers are tightened to provide a secure connection.
Step 5: Check the Injection Path
The applicator verifies that the drilled holes communicate with the crack or joint.
Depending on the system and site conditions, controlled water flushing may be used.
However, flushing is not suitable for every resin or situation.
The manufacturer's method statement must be followed.
Step 6: Inject the PU Resin
The PU resin is injected using a suitable grouting pump.
Injection normally begins at the lowest practical point for a vertical water-bearing crack.
The resin enters the crack and reacts with the available moisture.
As the material expands, water flow may begin to reduce.
Injection is continued under controlled pressure until the required filling or refusal criteria are achieved.
Excessive pressure must be avoided.
High injection pressure can damage weak concrete, widen cracks or create new leakage paths.
This is one reason experienced applicators are important.
Step 7: Inspect and Reinject Where Necessary
Once the resin has reacted, the treated area is inspected.
If leakage continues, additional injection may be required.
Some repairs require a second resin system to provide a more durable seal.
Step 8: Remove Packers and Finish the Surface
After the resin has cured sufficiently:
-
Packers are removed or cut flush
-
Drill holes are sealed using suitable repair mortar
-
The surface is cleaned
-
Leakage is monitored
The repaired area should be inspected again under representative water-pressure conditions wherever practical.
5. Why PU Injection Sometimes Fails

PU injection is effective, but it is not magic.
We have seen situations where injection was carried out repeatedly without resolving the underlying problem.
The common reasons include:
Wrong Resin Selection
A rapidly expanding foam may stop water temporarily but may not provide the required long-term seal for every application.
Some resins need continuing moisture to maintain their properties, while others form more dimensionally stable seals.
Product selection matters.
Incorrect Packer Placement
If the drilled hole does not intersect the crack, the resin may never reach the actual leakage path.
The applicator may consume significant material without stopping the leak.
Excessive Injection Pressure
More pressure does not automatically mean better waterproofing.
Excessive pressure can damage the surrounding concrete or force resin into unintended locations.
Incomplete Injection
The visible leak may stop while interconnected voids remain untreated.
Water may subsequently find another route.
Structural Movement
If a crack is continuing to widen because of settlement, structural deflection or ongoing thermal movement, injection alone will not solve the problem. The cause of movement needs engineering attention first, and the crack may then need a flexible resin system designed for moving cracks.
6. What Does PU Injection Grouting Cost in India?
Indicative 2026–27 market planning figures — actual quotes vary with access, water flow, wall thickness and city. Always confirm against a site visit:
- Applied cost (material + packers + labour): roughly ₹350–900 per running metre of treated crack or joint; difficult-access or high-flow situations can run higher.
- Typical residential basement job: most land between ₹15,000 and ₹60,000, depending on how many metres of joints are weeping.
- Material: Sika Injection-101 IN, a flexible water-reactive closed-cell PU injection foam, is ₹6,500 per pack with us. One pack typically treats several running metres, but consumption depends entirely on crack volume and water flow — keep a margin.
Compare that with excavating outside a basement wall to re-waterproof it externally — easily ₹1,50,000 or more, plus weeks of disruption. Injection from the inside is almost always the economical first line of attack.
7. Products and Accessories
For active water leakage: Sika Injection-101 IN. For dormant structural cracks needing bonding strength: Sikadur-31 IN epoxy (₹3,600). Packers, injection pumps and secondary resins are arranged against requirement — message us with your running-metre measurement and a photo of the leak on WhatsApp and we will size the complete kit, with a GST invoice and Pan-India dispatch from Jaipur. Items not in ready stock are procured against your order with an additional 4–5 working days, confirmed upfront.
8. Should You Do It Yourself?
Honest answer: a small, low-pressure weep on an accessible wall — yes, with a hand pump, packers and patience. Active flows, deep basements, or anything structural — use an experienced applicator; the real skill is pressure control and knowing when to stop injecting. We supply the same materials to both, and Divya on WhatsApp will tell you plainly which side of that line your problem falls on — free advice, no sales pressure.
Related Reading
- Basement waterproofing that survives the water table
- Underground water tank waterproofing (potable-safe)
- Concrete crack repair: polymer vs epoxy vs PU injection
Frequently Asked Questions
Does PU injection stop leaks permanently?
The cured foam is durable and stays flexible, so it accommodates minor movement. Joints under continuing structural movement may need re-treatment after some years — still far cheaper than excavation.
Can it be done during monsoon, while the leak is running?
Yes. PU injection is one of the few waterproofing methods that needs water to react — active leakage actually helps the foam expand and seal.
How much material should I order?
Measure the running metres of leaking crack or joint and share it on WhatsApp — we will size the packs for you rather than have you over-buy.